Linux Config Commands

By

13 Linux Network Configuration and Troubleshooting Commands

Computers are connected in a network to exchange information or resources each other. Two or more computer connected through network media called computer network. There are number of network devices or media are involved to form computer network. Computer loaded with Linux Operating System can also be a part of network whether it is small or large network by its multitasking and multiuser natures. Maintaining of system and network up and running is a task of System / Network Administrator’s job. In this article we are going to review frequently used network configuration and troubleshoot commands in Linux.
Linux Network Configuration and Troubleshooting Commands

1. ifconfig

ifconfig (interface configurator) command is use to initialize an interface, assign IP Address to interface and enable or disable interface on demand. With this command you can view IP Address and Hardware / MAC address assign to interface and also MTU (Maximum transmission unit) size.
# ifconfig

eth0      Link encap:Ethernet  HWaddr 00:0C:29:28:FD:4C
          inet addr:192.168.50.2  Bcast:192.168.50.255  Mask:255.255.255.0
          inet6 addr: fe80::20c:29ff:fe28:fd4c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:6093 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4824 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6125302 (5.8 MiB)  TX bytes:536966 (524.3 KiB)
          Interrupt:18 Base address:0x2000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:480 (480.0 b)  TX bytes:480 (480.0 b)
 
ifconfig with interface (eth0) command only shows specific interface details like IP Address, MAC Address etc. with -a options will display all available interface details if it is disable also.
# ifconfig eth0

eth0      Link encap:Ethernet  HWaddr 00:0C:29:28:FD:4C
          inet addr:192.168.50.2  Bcast:192.168.50.255  Mask:255.255.255.0
          inet6 addr: fe80::20c:29ff:fe28:fd4c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:6119 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4841 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6127464 (5.8 MiB)  TX bytes:539648 (527.0 KiB)
          Interrupt:18 Base address:0x2000

Assigning IP Address and Gateway

Assigning an IP Address and Gateway to interface on the fly. The setting will be removed in case of system reboot.
# ifconfig eth0 192.168.50.5 netmask 255.255.255.0

Enable or Disable Specific Interface

To enable or disable specific Interface, we use example command as follows.
Enable eth0
# ifup eth0
Disable eth0
# ifdown eth0

Setting MTU Size

By default MTU size is 1500. We can set required MTU size with below command. Replace XXXX with size.
# ifconfig eth0 mtu XXXX

Set Interface in Promiscuous mode

Network interface only received packets belongs to that particular NIC. If you put interface in promiscuous mode it will received all the packets. This is very useful to capture packets and analyze later. For this you may require superuser access.
# ifconfig eth0 - promisc

2. PING Command

PING (Packet INternet Groper) command is the best way to test connectivity between two nodes. Whether it is Local Area Network (LAN) or Wide Area Network (WAN). Ping use ICMP (Internet Control Message Protocol) to communicate to other devices. You can ping host name of ip address using below command.
# ping 4.2.2.2

PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data.
64 bytes from 4.2.2.2: icmp_seq=1 ttl=44 time=203 ms
64 bytes from 4.2.2.2: icmp_seq=2 ttl=44 time=201 ms
64 bytes from 4.2.2.2: icmp_seq=3 ttl=44 time=201 ms

OR

# ping www.tecmint.com

PING tecmint.com (50.116.66.136) 56(84) bytes of data.
64 bytes from 50.116.66.136: icmp_seq=1 ttl=47 time=284 ms
64 bytes from 50.116.66.136: icmp_seq=2 ttl=47 time=287 ms
64 bytes from 50.116.66.136: icmp_seq=3 ttl=47 time=285 ms
In Linux ping command keep executing until you interrupt. Ping with -c option exit after N number of request (success or error respond).
# ping -c 5 www.tecmint.com

PING tecmint.com (50.116.66.136) 56(84) bytes of data.
64 bytes from 50.116.66.136: icmp_seq=1 ttl=47 time=285 ms
64 bytes from 50.116.66.136: icmp_seq=2 ttl=47 time=285 ms
64 bytes from 50.116.66.136: icmp_seq=3 ttl=47 time=285 ms
64 bytes from 50.116.66.136: icmp_seq=4 ttl=47 time=285 ms
64 bytes from 50.116.66.136: icmp_seq=5 ttl=47 time=285 ms

--- tecmint.com ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4295ms
rtt min/avg/max/mdev = 285.062/285.324/285.406/0.599 ms

4. NETSTAT Command

Netstat (Network Statistic) command display connection info, routing table information etc. To displays routing table information use option as -r.
# netstat -r

Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
192.168.50.0    *               255.255.255.0   U         0 0          0 eth0
link-local      *               255.255.0.0     U         0 0          0 eth0
default         192.168.50.1    0.0.0.0         UG        0 0          0 eth0

5. DIG Command

Dig (domain information groper) query DNS related information like A Record, CNAME, MX Record etc. This command mainly use to troubleshoot DNS related query.
# dig www.tecmint.com; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6 <<>> www.tecmint.com
;; global options: +cmd
;; Got answer:
;; ->>HEADER<

6. NSLOOKUP Command

nslookup command also use to find out DNS related query. The following examples shows A Record (IP Address) of tecmint.com.
# nslookup www.tecmint.com
Server:         4.2.2.2
Address:        4.2.2.2#53

Non-authoritative answer:
www.tecmint.com canonical name = tecmint.com.
Name:   tecmint.com
Address: 50.116.66.136

7. ROUTE Command

route command also shows and manipulate ip routing table. To see default routing table in Linux, type the following command.
# route

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.50.0    *               255.255.255.0   U     0      0        0 eth0
link-local      *               255.255.0.0     U     1002   0        0 eth0
default         192.168.50.1    0.0.0.0         UG    0      0        0 eth0
Adding, deleting routes and default Gateway with following commands.
Route Adding
# route add -net 10.10.10.0/24 gw 192.168.0.1
Route Deleting
# route del -net 10.10.10.0/24 gw 192.168.0.1
Adding default Gateway
# route add default gw 192.168.0.1

8. HOST Command

host command to find name to IP or IP to name in IPv4 or IPv6 and also query DNS records.
# host www.google.com

www.google.com has address 173.194.38.180
www.google.com has address 173.194.38.176
www.google.com has address 173.194.38.177
www.google.com has address 173.194.38.178
www.google.com has address 173.194.38.179
www.google.com has IPv6 address 2404:6800:4003:802::1014
Using -t option we can find out DNS Resource Records like CNAME, NS, MX, SOA etc.
# host -t CNAME www.redhat.com

www.redhat.com is an alias for wildcard.redhat.com.edgekey.net.

9. ARP Command

ARP (Address Resolution Protocol) is useful to view / add the contents of the kernel’s ARP tables. To see default table use the command as.
# arp -e

Address                  HWtype  HWaddress           Flags Mask            Iface
192.168.50.1             ether   00:50:56:c0:00:08   C                     eth0

10. ETHTOOL Command

ethtool is a replacement of mii-tool. It is to view, setting speed and duplex of your Network Interface Card (NIC). You can set duplex permanently in /etc/sysconfig/network-scripts/ifcfg-eth0 with ETHTOOL_OPTS variable.
# ethtool eth0

Settings for eth0:
        Current message level: 0x00000007 (7)
        Link detected: yes

11. IWCONFIG Command

iwconfig command in Linux is use to configure a wireless network interface. You can see and set the basic Wi-Fi details like SSID channel and encryption. You can refer man page of iwconfig to know more.
# iwconfig [interface]

12. HOSTNAME Command

hostname is to identify in a network. Execute hostname command to see the hostname of your box. You can set hostname permanently in /etc/sysconfig/network. Need to reboot box once set a proper hostname.
# hostname 

tecmint.com

13. GUI tool system-config-network

Type system-config-network in command prompt to configure network setting and you will get nice Graphical User Interface (GUI) which may also use to configure IP Address, Gateway, DNS etc. as shown below image.
# system-config-network
Linux GUI Network Configuration
Linux GUI Network Configuration Tool
This article can be useful for day to day use of Linux Network administrator in Linux / Unix-like operating system. Kindly share through our comment box if we missed out.

Comments

Post a Comment

Popular posts from this blog

How to Create a Yoga Goddess Illustration in Adobe Illustrator

By
Image
As the music begins to play, a soft breeze fills the space with the undeniable smell of magnolia blossoms. She gracefully enters and begins a “tree pose” with her hands in Namaste form. Our female figure is inspired by the Indian culture for its gorgeous use of color and the grace of its yoga formations. I hope you’ll enjoy the journey as we retrace, step by step to enlightenment.  1. Becoming Flesh and Blood Step 1 Our first step will be to bring in our sketch. I've scanned her in at 300 dpi to catch as much of the detail as possible. I'm not as picky about my choice of initial drawing tools, and this particular project was completed with a mechanical pencil. We'll be working with a clean line quality from Adobe Photoshop and now we can begin to work. I'm working in Adobe Illustrator at a size of 8.5 x 11 inches for this specific project. When I'm ready to start my layers, I'll label my first layer as "Sketch" and lock the layer to make su...
Read more

How to Create an Icon Set using Adobe Photoshop

By
Image
In this tutorial, we are going to design a set of icons in Adobe Photoshop. An icon set needs to have the same background and theme. For learning purposes, we are going to design a sun icon, an ice flake icon, and an RSS icon. Let's get started. 1. Preparing the Canvas Step 1 Start by making a new file with size 350 px × 350 px . Click the small box next to the  Background Contents  option to change the new canvas color. Step 2 In the Color Picker dialog box, select grey ( #e0e0e2 ) for the canvas background color. Step 3 It is always a good idea to keep your work structured from the start. Make a new layer group and name it  sun . This is where we will place all layers used in the sun icon. 2. Designing the Icon Base Step 1 Use the  Rounded Rectangle Tool  to draw a rectangle with size  83 px × 64 px and  8 px  radius. To get accurate results, use the  Properties  panel. In this panel, you can simply enter the exact siz...
Read more

Android Hacking and Security, : Insecure Local Storage: Shared Preferences

By
Image
Background Device loss is a very common problem with mobile devices. An attacker who has physical access to the device can have access to personal as well as corporate data stored in the device. The situation could be worse if the device is rooted. Keeping this in mind, if the data storage mechanisms being used by an application are not implemented properly, it may lead to serious attacks. Android local data storage techniques Developers can store data in Android applications locally in various ways, as shown below. Shared Preferences Shared Preferences are XML files to store private primitive data in key-value pairs. Data Types include Booleans, floats, ints, longs, and strings. SQLite Databases SQLite databases are lightweight file-based databases. They usually have the extension “.db” or “.sqlite”. Android provides full support for SQLite databases. Databases we create in the application will be accessible to any class in the application. Other apps cannot acc...
Read more